該快速冷卻滅菌柜嚴格按照GMP標準設計制作，主要用于制藥行業對玻璃瓶裝大輸液、口服液產品進行高溫蒸汽滅菌操作和冷卻、清洗處理。
對于輸液類產品，需要高溫狀態來殺滅細菌的芽孢，同時又要盡量減少高溫滅菌對產品本身的影響，特別是對溫度較為敏感的產品尤甚。因此，快速升溫滅菌及滅菌后快速冷卻是程序控制出現后最早提出的概念。而“快速冷卻滅菌柜”很好地解決了這個問題。
輸液產品是溫度與壓力比較滯后性較大的品種，初期產品測溫點采樣并不精確。該快速冷卻滅菌柜采取實測輸液溫度來達到精確控溫，確保滅菌當量值（F0值）達到工藝要求，同時保證冷卻階段真正達到安全的冷卻溫度。在整個工作過程中，確保所有參數在設定的工藝下運行。
該設備采用微機觸摸屏人機界面操作設定系統，西門子PLC全程檢測控制。F0值與溫度時間雙重測控確保滅菌效果，滅菌報表由打印機輸出以存檔備案。
該設備工作過程中采用循環水與蒸汽混合加熱的工作方式，確保溫度的均勻性。滅菌后通過逐步冷卻循環水對輸液降溫，安全可靠。整個工作過程控制在90分鐘左右，最終產品冷卻溫度控制在60℃以下。（冷卻溫度可以根據環境溫度作適當調整）
The rapid cooling sterilization cabinet is designed and manufactured in strict accordance with GMP standards, and is mainly used for high temperature steam sterilization, cooling and cleaning of glass bottled infusion and oral liquid products in the pharmaceutical industry.
For infusion products, high temperature is required to kill bacterial spores, while minimizing the impact of high temperature sterilization on the product itself, especially for products sensitive to temperature.Therefore, rapid heating sterilization and rapid cooling after sterilization were the earliest concepts proposed after the emergence of program control.And the "rapid cooling sterilization cabinet" solved this problem well.
Infusion product is a kind of product with lag between temperature and pressure, and the sampling of temperature measuring point of initial product is not accurate.The rapid cooling sterilization cabinet adopts the measured infusion temperature to achieve accurate temperature control, to ensure that the sterilization equivalent value (F0 value) meets the process requirements, and to ensure that the cooling stage truly achieves a safe cooling temperature.During the whole working process, ensure that all parameters operate under the set process.
The equipment adopts the computer touch screen human-machine interface operation setting system, Siemens PLC full-range detection and control.Dual measurement and control of F0 value and temperature and time ensure sterilization effect, and sterilization report is output by printer for archiving.
The equipment adopts the working mode of mixing heating of circulating ** and steam to ensure the uniformity of temperature.After sterilization, cooling the infusion by gradually cooling the circulating ** is safe and reliable.The whole working process is controlled in about 90 minutes, and the final product cooling temperature is controlled below 60 C.(Cooling temperature can be adjusted appropriately according to ambient temperature)
2006-2025 上海博華國際展覽有限公司版權所有（保留一切權利）
滬ICP備05034851號-57
